In a SAS stack of shelves, what is the topology of the connection between expander and disk?
Which type of AutoSupport message would you expect to see triggered automatically when ONTAP software detects a NetApp WAFL inconsistency on an aggregate?
In the latest MANAGEMENT LOG AutoSupport message, you try to inspect the ENVIRONMENT section but find it empty.
In which section of AutoSupport can you find the reason?
A storage administrator is troubleshooting a 4-node cluster, where one node is reporting “cluster port is down†alerts. The node has recently been recabled to new cluster switches. The cluster ping-cluster command shows communication failures between the affected node and its partners over the cluster network. All physical cables have been verified as properly seated and undamaged.
Which configuration is causing this problem?
Your customer notices that their AFF A220 high-availability (HA) system is showing Single-Path HA.

How do you make the system into multipath HA?
When you add a new disk to an ONTAP 9.1 system, you see an error that the disk “has raid label with version (16), which is not within the currently supported range (14-15).†What is one possible cause of this error?
You have replaced the cluster backend switches on a 4-node NetApp ONTAP cluster with new switches. After the replacement, you realize that the system shows errors for the old switches that were removed:

You also notice that system switch ethernet show shows four switches, the two old switches and the two new switches.
What action will resolve the issue?
On an AFF A700 system, a SAS stack is connected to SAS ports 2a and 2b. The system has an additional 4-port SAS card in slot 9.
How should the cabling the corrected for best practices?
Which of the following scenarios could result in a NetApp WAFL inconsistency in a RAID DP aggregate?
During a health check you observe that NetApp ONTAP software is reporting CRC errors on a network port from a node in the cluster.
Which component do you reseat?
In which two sections of AutoSupport can you find information to analyze the following panic? (Choose two.)
Panic_Message: PCI Error NMI from device(s):ErrSrcID(CorrSrc(0xf00),UCorrSrc(0x18)), RPT(0,3,0):Qlogic FC 16G adapter in slot 1 on Controller
Which two tools can be used to recover an inconsistent aggregate? (Choose two.)
Which two of the following methods are valid ways to access a node which is not booting? (Choose two.)
You are upgrading your 6-node NetApp ONTAP cluster from ONTAP 9.9.1 to 9.16.1. As part of the ONTAP software upgrade process, you need to update the cluster switches. After you update the first switch, you receive the following AutoSupport message:
Exhibit — AutoSupport Alert
vifmgr: callhome.clus.net.degraded:alert:
Call home for CLUSTER NETWORK DEGRADED:
Large MTU Packet Loss - Ping failures detected
between Node1_clus1 (169.254.2.94) on Node1
and Node2_clus2 (169.254.248.67) on Node2.
All cluster ports and interfaces are in an up/up status.
What is causing this error?
Where is a kernel core file stored on a FAS9000 system that is running ONTAP 9.12.1 software?
You have replaced a failed boot device. You perform boot_recovery and receive no errors. However, when the node reboots, it reports that it has no disks.
What are two possible causes? (Choose two.)
A SAS connection is reporting a single PHY down.
What are the two most likely causes? (Choose two.)
Which three commands can be used to manually generate a kernel core file? (Choose three.)
A node has panicked with a PCI/NMI error. Giveback has not been performed.
Which two commands should you run to collect the logs to determine the cause? (Choose two.)
Following an unexpected takeover, the taken-over node is waiting for giveback. The administrator plans to perform a giveback with the option –cfo–only true.
What happens if this option is used?