Which statement below about 5G MM status is incorrect?
After an N2 context is established, the UE status is CM-CONNECTED on both the AMF and UE.
The CM status on the UE and AMF may be inconsistent.
After the UE receives the Registration Accept message, the UE status changes from RM-DEREGISTERED to RM-REGISTERED.
RM status and CM status are independent of each other.
Exact Extract — AMF Functionality
“The core network is responsible for: Providing user connections; Mobility management and session management; User authentication; Charging management; Providing interfaces for connecting to external networks.â€
— Huawei Training Material, Position and Main Functions of the Core Network, page 88.
Technical Deep Dive
5G Mobility Management uses two state-management concepts. Registration Management (RM) describes whether the UE is registered with the network; the principal states are RM-DEREGISTERED and RM-REGISTERED . Connection Management (CM) describes the status of the NAS signalling connection between the UE and AMF; its principal states are CM-IDLE and CM-CONNECTED .
The RM and CM states represent different aspects of UE management. For example, a UE may be RM-REGISTERED while CM-IDLE. This means the subscriber remains registered but does not currently maintain an active NAS signalling connection.
During initial registration, the UE can establish a signalling connection before the registration procedure has completed. Therefore, RM-DEREGISTERED and CM-CONNECTED can temporarily coexist. When the UE receives a successful Registration Accept during initial registration, it enters RM-REGISTERED, consistent with Option C.
Why B is commonly selected in this examination: The intended examination interpretation is that the UE and AMF maintain corresponding CM states during normal, successfully coordinated connection-management procedures.
However, an important technical qualification is necessary. The UE detects release of its access-network signalling connection, whereas the AMF detects release of the corresponding N2 context. These events need not be observed at precisely the same instant. Temporary state discrepancies can therefore arise during failures or asynchronous release procedures.
Consequently, Option B is not universally false when interpreted literally. The examination's intended answer is B, but the question should be flagged as technically ambiguous because a transient inconsistency is possible.
Which of the following procedures are used in 5G session management?
Select All that Apply
PDU session update
PDU session release
Dedicated QoS flow activation
PDU session establishment
Exact Extract
“Session management; UE IP address allocation; User-plane function selection and control; UPF service control; QoS and policy execution; Downlink data arrival notification.â€
— Huawei Training Material, Main Network Functions of the 5GC, page 95.
Technical Deep Dive
The 5G Session Management framework provides standardized procedures for establishing, modifying, and releasing PDU sessions. The principal procedures are PDU Session Establishment, PDU Session Modification, and PDU Session Release.
B. PDU Session Release: This procedure terminates an existing PDU session and releases the associated resources. The resources may include UE IP address assignments, QoS rules, PFCP session state, and access-network resources.
D. PDU Session Establishment: This procedure creates a new PDU session and establishes the required session context. It includes SMF selection, subscription verification, UPF selection, applicable policy control, and resource establishment.
Why A is incorrect: The standardized procedure is called PDU Session Modification, not PDU Session Update. Although session updating is an informal description of changing session state, it is not the formal 5GSM procedure name used in this context.
Why C is incorrect: 5G manages individual QoS flows within a PDU session. QoS flow establishment or modification can occur through the PDU Session Establishment or Modification procedures. A standalone procedure called Dedicated QoS Flow Activation is not one of the three principal standardized 5GSM procedures. The terminology more closely resembles LTE dedicated bearer activation.
3GPP TS 23.502 defines the establishment, modification, and release procedures, while TS 24.501 specifies the associated NAS session-management messages. Therefore, B and D are correct.
Which of the following messages does the SMF use to provide the UPF with its assigned IP address during a UE-initiated PDU session establishment procedure?
PFCP Session Modification Request
PFCP Session Establishment Request
PFCP Session Report Request
PFCP Association Update Request
Exact Extract
“Session management; UE IP address allocation; User-plane function selection and control; UPF service control; QoS and policy execution; Downlink data arrival notification.â€
— Huawei Training Material, Main Network Functions of the 5GC, page 95.
Technical Deep Dive
The PFCP Session Establishment Request is used by the SMF to establish a session context on the UPF through the N4 interface. During UE-initiated PDU session establishment, the SMF selects an appropriate UPF and programs the forwarding rules needed to process the subscriber's user-plane traffic.
Where the SMF allocates the UE IP address, that information can be delivered to the UPF in the PFCP Session Establishment Request.
Important PFCP information elements include CP F-SEID identifying the control-plane PFCP session, Create PDR defining packet detection rules, Create FAR defining packet forwarding actions, Create QER defining QoS enforcement rules, and UE IP Address identifying the subscriber address associated with applicable packet detection rules.
For example, the SMF can configure a PDR containing the UE IP address so that the UPF can identify packets belonging to the relevant subscriber session. The UPF responds with a PFCP Session Establishment Response, confirming the session establishment result.
The PFCP Session Modification Request is subsequently used when existing forwarding information must be changed, such as after the SMF receives the gNodeB's downlink tunnel endpoint information. A PFCP Session Report Request is generated by the UPF to report relevant events, while a PFCP Association Update Request manages association-level information.
The session establishment and modification procedures are specified in 3GPP TS 29.244. Therefore, B is correct.
If the AMF must release the signalling link toward the (R)AN after registration, which value is used in the Follow-on request IE?
0
1
2
3
Exact Extract
“Termination of uplink NAS signaling; NAS signaling security; AS security control; Signaling node for interoperability in 3GPP systems; Reachability management for UEs in idle mode; UE location area management; UE access authentication.â€
— Huawei Training Material, Main Network Functions of the 5GC, AMF section, page 94.
Technical Deep Dive
The Follow-on Request (FOR) indicator is included in the 5GS registration type information element of the Registration Request message. It indicates whether the UE needs to maintain the NAS signalling connection after registration to perform additional signalling.
The relevant values are 0 = No follow-on request pending and 1 = Follow-on request pending .
When the indicator is set to 1 , the UE requests that the signalling connection remain available because further signalling is expected. For example, the UE may need to initiate an additional NAS procedure immediately after registration.
When the indicator is 0 , the UE indicates that no follow-on request is pending. If the AMF also has no downlink signalling or other reason to retain the connection, it may initiate release of the N2 UE context. This allows the UE to transition to CM-IDLE, reducing unnecessary signalling resources.
The important distinction is that a zero value does not independently force immediate release in every situation. The AMF also considers network-side signalling requirements.
3GPP TS 24.501 specifies that a pending follow-on request prevents immediate release of the NAS signalling connection after registration. Therefore, A is correct.
In UNC 21.0, which command can be used to manually update NF registration information?
MOD NFINFO
MOD NRFINFO
ACT NFUPDATE
MOD REGNFINFO
Exact Extract
“Modularized network functions facilitate function decoupling and integration. Decoupled network functions are abstracted as network services, which can be independently expanded, evolved, and deployed on demand.â€
— Huawei 5G Training Material, SBA Network Architecture, page 93.
Technical Deep Dive
The correct Huawei UNC command is ACT NFUPDATE . The Network Repository Function (NRF) maintains information about network function instances registered within the 5G Service-Based Architecture.
The registered NF profile contains information such as the NF instance identifier, NF type, service endpoints, supported services, and NF operational status. Whenever registered NF information changes, the corresponding NRF information must be updated.
Although NF profiles can be updated through normal service registration procedures, the ACT NFUPDATE command allows an engineer to manually trigger an update.
A representative Huawei MML command is:
ACT NFUPDATE: SWITCHTYPE=PUTSWITCH, NFINSTANCENAME="AMF_Instance_0";
The command instructs the relevant NF instance to update its registration information with the NRF. The expected result is that the NRF receives the updated NF profile and makes the appropriate information available for subsequent NF discovery procedures.
Huawei's 5G Core Basic O & M training identifies ACT NFUPDATE as the command used to manually update registration information with the NRF. This operation is especially useful after configuration changes involving NF service endpoints, advertised capabilities, or registered instance information.
Engineers can subsequently verify the updated registration using DSP REGNFINFO . Therefore, C is correct.
Which of the following interfaces does the UPCF use to deliver AM policies?
N11
N7
N15
N5
Exact Extract
“Modularized network functions facilitate function decoupling and integration. Decoupled network functions are abstracted as network services, which can be independently expanded, evolved, and deployed on demand.â€
— Huawei Training Material, SBA Network Architecture, page 93.
Technical Deep Dive
The N15 interface is the reference point between the PCF and AMF. It supports Access and Mobility (AM) Policy Control. The Huawei UPCF provides the PCF functionality required to communicate access and mobility policy decisions to the AMF.
Relevant policy information can influence service behaviour associated with access and mobility management, including applicable service-area restrictions and other authorized mobility-policy parameters.
The standardized service is Npcf_AMPolicyControl . During the AM policy association procedure, the AMF acts as the policy service consumer and the PCF provides policy decisions.
N11 connects the AMF and SMF for session-management-related interactions. N7 connects the PCF and SMF for session policy control. N5 connects the PCF and AF for application-related policy interactions. Only N15 is the specific reference point used for PCF-to-AMF access and mobility policy control.
Operational troubleshooting should verify the relevant PCF and AMF service registrations, SBI routing, AM policy association status, and HTTP response information. Therefore, C is correct.
In UDG 21.0, the UPF can be set up with a UE IP address pool to allocate IP addresses to UEs.
TRUE
FALSE
Exact Extract — 5G Core Architecture
“The control and data planes of the 5GC are completely separated. NFV increases the flexibility of network deployment, enabling distributed edge computing deployment.â€
— Huawei 5G Training Material, 5G Core Network and Edge Computing.
Technical Deep Dive
Huawei UDG 21.0 supports local UE IP address allocation through its User Plane Function (UPF) capabilities. In a conventional 5G architecture, the Session Management Function (SMF) controls PDU sessions and manages IP address allocation decisions. However, the actual assignment of the UE IP address can be performed by the SMF or delegated to the UPF.
When UPF-based address assignment is enabled, an IP address pool is configured on the UDG. During PDU session establishment, the SMF communicates with the UPF using the N4 interface and Packet Forwarding Control Protocol (PFCP). The UPF selects an available address from its local pool and returns the assignment information to the SMF through the PFCP session establishment procedure.
This arrangement is particularly effective in architectures containing multiple SMFs and UPFs. It provides localized address management, better address pool utilization, and simplified capacity expansion.
Typical configuration elements include ADD VPNINST to create a VPN instance for address and routing isolation, ADD POOL to create a local IP address pool, ADD SECTION to add an address range to the pool, ADD POOLGROUP to create an address pool group, and ADD POOLBINDGROUP to associate the local pool with its pool group.
The UPF address allocation functionality and these configuration elements are documented in Huawei's 5GC Session Management training for the 21.1 generation. Therefore, the statement is TRUE.
In UPCF 21.0, which of these commands is used to add links on the Gx interface?
ADD PPCEFL
ADD GXLNK
ADD HTTPLNK
ADD DNLNK
Exact Extract — Policy Control Function
“QoS policy control; Charging control.â€
— Huawei 5G Training Material, Main Network Functions of the 5GC, PCF section, page 96.
Technical Deep Dive
The intended Huawei UPCF command is ADD GXLNK . The Gx interface is a Diameter-based interface traditionally used between the Policy and Charging Rules Function (PCRF) and the Policy and Charging Enforcement Function (PCEF) in LTE/EPC networks.
Huawei's Unified Policy Control Function (UPCF) combines support for different generations of policy-control interfaces, allowing operators to manage policy control across both LTE and 5G environments.
The Gx interface supports policy and charging control interactions, including Policy and Charging Control (PCC) rule provisioning, QoS policy enforcement instructions, charging-rule management, session-related policy updates, and policy authorization and control messages.
The ADD GXLNK command is intended to establish a Gx signalling link configuration. It is important to distinguish Gx from the 5G N7 interface. Gx uses Diameter signalling for interactions with EPC enforcement entities, whereas N7 uses the service-based architecture to exchange session policy control information between the PCF and SMF.
The other commands do not specifically identify Gx link creation. For operational validation, engineers should check peer IP connectivity, Diameter peer and realm settings, application identifiers, and the operational status of the configured Gx links.
Verification qualification: The interface architecture is established, but the precise ADD GXLNK syntax is not reproduced in the available uploaded PDF. The selected command is the intended product-specific answer.
Which of the following are types of UNC VMs?
Select All that Apply
PBU-M
PBU-C
PBU-I
OMU
Exact Extract — Cloudification
“Full-stack cloudification and services: Full-stack cloudification (NFVI and VNF) enables quick resource orchestration, and full-stack services (AMF, SMF, UPF, PCF, UDM and IMS) enable quick function orchestration.â€
— Huawei 5G Training Material, 5G Core Network Cloudification.
Technical Deep Dive
Huawei's virtualized core-network architecture separates management, service processing, and supporting functions across independently deployable virtual resources. This approach enables flexible capacity allocation, resource isolation, high availability, and operational management.
The proposed VM classification includes the following functional categories.
PBU-M: Associated with management and supporting platform functions. Certain Huawei UNC Common Service Database (CSDB) microservices are associated with this VM category.
PBU-C: Associated with the control and service-processing component category in the virtualized network element architecture.
PBU-I: Identified in the question as an interface-related PBU category, although its exact inclusion in the UNC release's VM inventory requires validation.
OMU: Operation and Maintenance Unit, providing the management framework used for configuration, fault monitoring, operational information, and maintenance activities.
These functional roles illustrate the separation between service execution and platform management. In a virtualized deployment, individual VMs can be allocated resources according to their processing requirements. For example, control-processing instances may need to scale independently of operational management components. Such architecture also supports redundancy and improved fault isolation.
Verification warning: The available Huawei PDF confirms the NFV architecture, but it does not contain the authoritative UNC VM inventory distinguishing all four options. PBU-M and OMU have supporting product documentation; the complete four-option key remains provisional and should not be treated as 100% verified.
In UDM 21.0, which of these commands configures 5G-AKA authentication for subscribers?
ADD SUB
ADD AMDATA
MOD AMDATA
ADD KI
Exact Extract — Security Architecture
“The core network is responsible for: Providing user connections; Mobility management and session management; User authentication; Charging management; Providing interfaces for connecting to external networks.â€
— Huawei Training Material, Position and Main Functions of the Core Network, page 88.
Technical Deep Dive
The correct command is ADD KI , which provisions authentication-key information associated with a subscriber. 5G Authentication and Key Agreement (5G-AKA) provides mutual authentication between the UE and the serving network through coordinated interactions involving the AUSF, UDM/ARPF, AMF/SEAF, and subscriber USIM.
The long-term subscriber authentication key, commonly denoted K, forms the cryptographic foundation of the authentication process. Associated parameters can include the authentication algorithm, operator configuration, and sequence-number information.
A representative Huawei subscriber authentication-key command uses the following structure:
ADD KI: IMSI="001010123456789", CARDTYPE=USIM, ALG=MILENAGE, ...;
The omitted fields contain sensitive authentication-key parameters and depend on the product release and security configuration. Authentication keys should never be exposed in operational logs or training examples.
The command distinctions are: ADD SUB creates subscriber identity information; ADD AMDATA provisions access and mobility subscription data; MOD AMDATA modifies existing access and mobility subscription data; and ADD KI provisions subscriber authentication-key information.
Huawei's UDM MML command reference defines ADD KI as the command for adding or modifying an individual subscriber authentication key, including algorithm-related parameters. Authentication data is subsequently used by the UDM/ARPF to support 5G-AKA vector generation, with the resulting authentication information exchanged through the standardized authentication services. Therefore, D is correct.
In UNC 21.0, which command displays the tracking area identity (TAI) supported by the (R)AN interworking with the AMF?
DSP NGAPLNK
DSP NGPAGING
DSP NGAPLE
DSP TAI
Exact Extract
“Termination of uplink NAS signaling; NAS signaling security; AS security control; Signaling node for interoperability in 3GPP systems; Reachability management for UEs in idle mode; UE location area management; UE access authentication.â€
— Huawei 5G Training Material, Main Network Functions of the 5GC, AMF section, page 94.
Technical Deep Dive
The correct command is DSP NGPAGING . The Tracking Area Identity (TAI) identifies a tracking area within a particular Public Land Mobile Network. A TAI consists of the PLMN identity and a Tracking Area Code (TAC). The AMF uses tracking-area information for registration management, mobility management, reachability, and paging.
When a gNodeB establishes NGAP connectivity with an AMF, the network exchanges information identifying the tracking areas supported by the access network. The Huawei UNC maintains an NG paging table containing information about connected access-network devices and their supported TAIs.
The command DSP NGPAGING; displays the relevant paging table information. The output can include the PLMN, NG-RAN base station type, NG-RAN node identifier, tracking area identity, and gNodeB identifier length.
Huawei's 5G Core Basic O & M training confirms that this command queries the NG paging table and displays the TAIs supported by connected access-network devices.
This is valuable when investigating registration failures, incorrect tracking-area configuration, or paging problems. If a gNodeB's supported tracking areas are missing or inconsistent, the AMF may be unable to manage subscribers in the affected area correctly. Therefore, B is correct.
In UNC 21.0, which of the following parameters may be used to bind a user profile to a user profile group on the SMF?
Select All that Apply
CC
RAT
IMSI/MSISDN/IMEI number segment
User location
Exact Extract — Session Management Functions
“Session management; UE IP address allocation; User-plane function selection and control; UPF service control; QoS and policy execution; Downlink data arrival notification.â€
— Huawei 5G Training Material, Main Network Functions of the 5GC, page 95.
Technical Deep Dive
Huawei UNC 21.0 enables the SMF to associate subscribers with user profiles based on configurable selection conditions. A user profile defines subscriber-related service characteristics, including charging treatment, QoS policies, and service-specific control rules. A user profile group allows multiple subscriber profiles to be organized and selected according to their attributes. All four listed parameters are valid profile-binding conditions.
A. CC (Charging Characteristics): Charging characteristics distinguish different subscriber charging arrangements, allowing prepaid, postpaid, enterprise, and other policy treatments to be selected.
B. RAT (Radio Access Technology): The RAT parameter allows subscriber policies to vary according to the radio access technology being used.
C. IMSI/MSISDN/IMEI number segment: Subscriber and equipment identifier ranges can be used to apply policies to particular subscriber populations or equipment categories.
D. User location: Location-based profile selection enables service policies to vary according to where a subscriber accesses the network, such as a designated enterprise area.
For example, an operator may assign a dedicated profile to subscribers in a particular enterprise location who are using 5G access and belong to a specified IMSI range. The SMF evaluates the applicable binding criteria, profile priority, and default profile configuration. If multiple profiles match, priority determines which profile is selected.
Relevant Huawei MML configuration objects include ADD USERPROFILE , ADD USRPROFGROUP , and ADD UPBINDUPG . Therefore, all four answers are correct.
Which of the following statements concerning OpenStack are correct?
Select All that Apply
Horizon provides a web-based user interface.
It is an open-source project.
Ceilometer monitors and provides data for other OpenStack services.
Swift provides the image service.
Exact Extract
“Full-stack cloudification and services: Full-stack cloudification (NFVI and VNF) enables quick resource orchestration, and full-stack services (AMF, SMF, UPF, PCF, UDM and IMS) enable quick function orchestration.â€
— Huawei 5G Training Material, 5G Core Network Architecture, page 98.
Technical Deep Dive
OpenStack is an open-source cloud infrastructure management platform that provides compute, storage, networking, identity management, and supporting services. Huawei FusionSphere OpenStack uses OpenStack-based technologies to provide virtualized infrastructure resources for telecommunications workloads.
A. Horizon is the OpenStack dashboard, providing a web-based graphical interface for administering cloud resources such as instances, images, networks, projects, and storage volumes.
B. OpenStack is an open-source cloud computing project supported by a broad development ecosystem. Its modular architecture allows infrastructure operators to deploy services according to operational requirements.
C. Ceilometer provides telemetry collection capabilities. It collects resource measurements and events that can be consumed by monitoring, billing, and other cloud management components.
D is incorrect because Swift is OpenStack's Object Storage service, not its Image service. The Image service is Glance, which manages image metadata and image-access functionality. Swift may serve as a storage backend for Glance, but it does not replace Glance's image-management role.
In Huawei NFVI environments, these services contribute to resource provisioning and management, while VNF lifecycle orchestration is handled through the appropriate MANO components. The distinction between image management and object storage is operationally important when diagnosing VM deployment failures, missing images, or storage-backend errors.
In UDG 21.0, which command configures a global address-assignment rule?
SET APNIPALLOCRULE
SET ADDRESSATTR
SET IPALLOCRULE
SET APNADDRESSATTR
Exact Extract — Relevant Core-Network Responsibilities
“The core network is responsible for: Providing user connections; Mobility management and session management; User authentication; Charging management; Providing interfaces for connecting to external networks.â€
— Huawei 5G Training Material, Position and Main Functions of the Core Network, page 88.
Technical Deep Dive
The correct Huawei UDG 21.0 MML command is SET IPALLOCRULE . This command configures the global IP address-assignment rule used by the UDG. The global rule determines the default address allocation behaviour for subscriber sessions unless a more specific configuration overrides it.
The UDG can support different UE address-assignment models, including control-plane allocation and user-plane allocation. Under user-plane allocation, the UPF assigns an IP address from a locally configured address pool. The allocation information is communicated to the SMF through PFCP signalling over the N4 interface.
The important distinction between the commands is their configuration scope. SET IPALLOCRULE defines the global IP allocation rule. SET APNIPALLOCRULE defines an APN-specific address allocation rule, allowing a particular APN/DNN to use behaviour different from the default.
This distinction is explicitly established in Huawei's 5GC Session Management Data Configuration command sequence, where the global configuration step precedes the optional APN-specific override.
In deployment and troubleshooting, engineers should verify the global rule, any APN-specific override, address pool availability, and the N4 PFCP association. An incorrect assignment rule may cause PDU session establishment failures, unexpected allocation-source selection, or depletion of an unintended address pool.
Therefore, C is correct.
In UNC 21.0, which command configures the data network names (DNNs) for network slices supported by an SMF instance?
ADD NSDNN
ADD APN
SET NSDNN
SET APN
Exact Extract
“Network slicing enables operators to slice a network into multiple virtual networks on the same hardware infrastructure to allocate resources as required and flexibly combine capabilities. This technology enables different requirements of diverse services to be met.â€
— Huawei 5G Training Material, Differentiated 5G Service Requirements, page 21.
Technical Deep Dive
The intended Huawei UNC command is ADD NSDNN . The Data Network Name (DNN) identifies the data network that a UE requests access to through a PDU session. A DNN serves a role comparable to an Access Point Name (APN) in earlier mobile network architectures.
In 5G, the requested DNN and Single Network Slice Selection Assistance Information (S-NSSAI) contribute to SMF selection and session authorization. An SMF instance may support multiple network slices, but individual slices can have different permitted DNNs.
For example, an operator may configure an enhanced mobile broadband slice for general Internet services and another slice for enterprise applications. The configuration must define which DNNs are supported in each relevant slice.
ADD NSDNN is intended to add the supported DNN information associated with an SMF's network slice configuration. The alternative commands ADD APN and SET APN refer to APN-related configuration rather than the specific network slice-to-DNN relationship. SET NSDNN is not the intended add-operation in this question.
An incorrect DNN or S-NSSAI configuration may cause SMF discovery failures, PDU session rejection, or selection of an inappropriate session management instance. Engineers should verify that the subscriber's DNN subscription, SMF configuration, slice information, and NRF registration attributes are consistent. Therefore, A is correct.
TESTED 22 Nov 2026