Which of the following server configurations is recommended for the optical fiber sensing scenario?
128 GB configuration
384 GB configuration
512 GB configuration
Relevant Training Extract — HUAWEI NCE-T Product Introduction, Page 125
“Optical fiber sensing — Commercial use — O1-Fiber Sensing Vibration Warning System Management Basic Package — managementâ€
Technical Deep Dive:
Huawei ' s optical fiber sensing solution incorporates distributed sensing equipment, event analysis, alarm processing, geographic visualization, and centralized management.
Optical sensing systems generate information about disturbances along monitored fiber routes. Depending on the implementation, these disturbances may be classified using signal-processing algorithms and machine-learning techniques.
Server resource planning must account for the monitored fiber scale, sensing event volume, number of managed devices, data retention requirements, and software processing architecture.
A larger memory configuration may be selected where the management infrastructure includes substantial analytics, correlation, or virtualization workloads.
The intended answer identifies a 384 GB server configuration for the referenced sensing deployment.
However, server sizing must distinguish between the physical machine deployment model and virtualized deployments. They may have different memory requirements even when they support similar business functions.
Technical Conclusion: B is the answer intended by the question set, but it cannot be established as a universal requirement from the uploaded training material.
Verification warning: The Huawei training identifies the sensing management function but does not specify a 384 GB memory requirement. Other Huawei release documentation identifies a 128 GB physical server for an optical-fiber sensing scenario and 384 GB for a combined Manager/Controller/Analyzer virtualized configuration. Consequently, this question requires an explicit software release and deployment scenario before a single memory recommendation can be considered fully verified.
Which of the following statements about the license configuration of enterprise WDM series are correct?
Select All that Apply
The cross-connect capacity license is used to control the expansion of the port capacity.
If the Fiber Doctor function is selected on the DC908, the intelligent fiber monitoring license will be configured.
To configure Liquid OTN services on the port of the line board, a Liquid OTN license is required.
If the IEEE 1588v2 feature is required, each set of devices on the clock tracing path requires one IEEE 1588v2 function license.
Exact Extract — Network Planning, Design, Configuration and Quotation Guide, Pages 61 and 67
“Capacity of Centralized Cross Connect Board: This parameter is used to configure a centralized cross-connect capacity license.â€
“Need 1588V2 Function or not: If the IEEE 1588v2 feature is required, each device on the clock tracing path requires one piece of IEEE 1588v2 function software.â€
Technical Deep Dive:
Huawei enterprise WDM systems use software licensing to enable selected optical transport capabilities and control the expansion of licensed resources.
Option A — Incorrect. A cross-connect capacity license controls the amount of traffic that the cross-connect architecture is authorized to switch or groom. Physical port capacity and line-port activation are distinct licensing dimensions. Increasing the cross-connect capacity does not automatically authorize additional physical line-port capacity.
Option B — Correct under the intended licensing scheme. Fiber Doctor provides optical fiber monitoring and fault-localization capabilities. It can use embedded OTDR technology to detect fiber abnormalities, locate faults, and support proactive optical cable maintenance. The associated intelligent fiber monitoring entitlement must be included where the feature is separately licensed.
Option C — Correct under the intended licensing scheme. Liquid OTN enables fine-granularity hard-pipe service transmission. Applicable line-board functions may require corresponding feature entitlements to support OSU-based service transport.
Option D — Correct. IEEE 1588v2 supports precision time synchronization through Precision Time Protocol (PTP) messaging. Every participating network element that requires the licensed synchronization functionality must be appropriately authorized.
Licensing only the source and destination devices is insufficient when intermediate devices are required to process or regenerate timing information.
Technical Conclusion: B, C, and D are the intended selections. The supplied training explicitly establishes D and the distinction underlying A. The exact Fiber Doctor and Liquid OTN license-product mappings in B and C require release-specific SCT verification; they are not individually documented in the uploaded slides.
Which of the following statements is incorrect?
The dispersion is in direct proportion to the fiber length.
The attenuation is in inverse proportion to the transmission distance.
The smaller the insertion loss, the better.
All of the above
Exact Extract — Huawei DC908 Solutions and Technologies Introduction, Page 94
“Real time data collection, analyze fiber attenuationâ€
Technical Deep Dive:
Optical transmission performance depends on several physical parameters, including attenuation, chromatic dispersion, polarization-mode dispersion, connector losses, and optical signal-to-noise ratio.
Option A — Correct.
For a uniform fiber with constant chromatic dispersion coefficient, accumulated chromatic dispersion increases proportionally with fiber length.
The accumulated dispersion can be calculated as:
D_total = D_λ × L
Where D_λ represents the fiber dispersion coefficient in ps/(nm·km), and L represents the fiber length in kilometers.
Option B — Incorrect.
Optical attenuation increases with transmission distance rather than decreasing inversely with it.
For a uniform fiber, total fiber attenuation is:
A_fiber = α × L
Where α is the attenuation coefficient in dB/km.
For example, if the attenuation coefficient is 0.2 dB/km, a 50 km fiber has approximately 10 dB of fiber attenuation, while a 100 km fiber has approximately 20 dB, excluding connector and splice losses.
Option C — Correct.
Lower insertion loss generally indicates better optical component transmission efficiency and leaves more margin in the optical power budget.
Option D — Incorrect as the intended selection.
Not all the preceding statements are incorrect.
Technical Conclusion: B is the correct answer because it reverses the relationship between fiber length and attenuation.
OptiXtrans E6600T supports SDH/PKT/OTN cross-connections.
TRUE
FALSE
Exact Extract — Huawei E9600 and E6600 Series Products and Industry Applications Introduction, Page 15
“No cross-connect capabilityâ€
Additional Huawei Technical Reference — Page 12
The E6600 product comparison distinguishes the E6616 and E6608 switching platforms from the E6608T optical-layer terminal subrack.
Technical Deep Dive:
The Huawei OptiXtrans E6600 series comprises several transport platforms with different service access, switching, and optical transmission capabilities.
The E6616 and E6608 support centralized cross-connect functionality for Optical Transport Network (OTN), Synchronous Digital Hierarchy (SDH), and packet-based services, subject to the installed system control and cross-connect board.
The E6608T has a different architecture.
It is designed primarily as an optical-layer terminal platform, supporting optical transmission functions and tributary-line integrated boards rather than centralized electrical cross-connections.
Huawei specifies that the E6608T does not provide cross-connect capacity.
Consequently, it cannot perform the same centralized ODUk, VC, and packet switching operations as the E6616 or E6608.
For example, an E6616 equipped with an appropriate cross-connect board can groom services arriving through different tributary interfaces and route them toward selected line interfaces. An E6608T does not provide that equivalent electrical switching matrix.
This distinction must be considered when selecting equipment for aggregation networks and service grooming applications.
Technical Conclusion: B is correct.
Typing correction: The question refers to OptiXtrans E6600T. The correct model designation is OptiXtrans E6608T. The original wording is preserved above, but the model name should be corrected in the examination database.
Which board type requires no optical layer, dispersion, or commissioning and provides an SDH-like experience?
Ponder
OA
OTU
PID
Exact Extract — E9600 and E6600 Series Products and Industry Applications Introduction, Page 21
“Turbo WDM: Free of Optical Layer, Dispersion Compensation, and Commissioning, SDH-Like Experienceâ€
The same page identifies PID-based networking, simplified optical transmission, unified service grooming, and segment-by-segment electrical regeneration.
Technical Deep Dive:
PID is associated with Huawei ' s simplified Turbo WDM architecture, which reduces the equipment complexity traditionally required for wavelength-division multiplexing networks.
Conventional WDM systems may require independent optical transponders, optical amplifiers, multiplexers, demultiplexers, and dispersion compensation equipment. These components increase the number of optical connections and require additional optical power engineering and commissioning activities.
Huawei ' s Turbo WDM solution integrates the necessary transmission functionality into a simplified architecture, minimizing the dependence on separate optical-layer subsystems for supported applications.
The solution supports Ethernet, SDH, and OTN service transmission while enabling unified grooming through the transport platform.
Its SDH-like operating model simplifies network planning, service configuration, and maintenance. Segment-by-segment electrical regeneration also makes fault isolation more straightforward than troubleshooting complex multi-span optical amplification chains.
Option A, Ponder, refers to optical transponder-related functionality and does not independently identify the complete simplified Turbo WDM solution. Option B, OA, is an optical amplifier, while option C, OTU, is an Optical Transponder Unit.
Technical Conclusion: D is correct. The phrase no optical layer means no separately engineered conventional optical-layer subsystem is required for the supported Turbo WDM design; it does not mean optical transmission occurs without optical-layer functions.
What is the primary difference between NCE-T and NCE-T Lite?
Different function
Different quotation item
Different network management scales
Exact Extract — Huawei DC908 Solutions and Technologies Introduction, Page 96
“Flexibly defined management and control solutions based on different network scalesâ€
The management comparison identifies iMaster NCE-T Lite for medium-sized DCI networks with fewer than 1,000 network elements and iMaster NCE-T for larger networks exceeding 1,000 network elements.
Technical Deep Dive:
The primary distinction between iMaster NCE-T and iMaster NCE-T Lite is the supported network management scale and associated deployment architecture.
iMaster NCE-T is an intelligent optical network management and control platform that supports centralized network supervision, topology management, performance monitoring, fault management, service provisioning, and network automation.
NCE-T Lite is optimized for enterprise and medium-sized optical transport deployments where a lighter management environment is sufficient.
The training architecture identifies three principal management scenarios:
• WebGUI/CLI: Single-device management without a dedicated management server.
• NCE-T Lite: Medium-sized networks, with simplified server deployment.
• NCE-T: Large-scale networks requiring a full server-based management environment.
Both editions belong to the same transport network management ecosystem, but their scale, deployment resources, licensing requirements, and supported feature combinations must be evaluated against the applicable release.
Technical Conclusion: Option C correctly identifies the principal difference.
Which of these service interfaces does the OptiXtrans E6600 series support?
Select All that Apply
GPON
OTN
SDH
PDH
SAN
ETH
Exact Extract — Huawei E9600 and E6600 Series Products and Industry Applications Introduction, Page 31
“Access of any 64 kbit/s to 100 Gbit/s services, including PCM, PDH, SDH, OTN, Ethernet, SAN, and video servicesâ€
Technical Deep Dive:
The Huawei OptiXtrans E6600 series is a multi-service optical transmission platform designed to integrate traditional TDM services with modern packet and optical transport technologies.
Option A — GPON (Incorrect): Gigabit Passive Optical Network is primarily a passive optical access technology used by OLT and ONU equipment. It is not listed as a native E6600 service interface.
Option B — OTN (Correct): Optical Transport Network provides high-capacity digital transport through standardized containers and transmission structures, including ODUk-based service transport.
Option C — SDH (Correct): Synchronous Digital Hierarchy supports synchronous TDM service transport, which remains important for utility and industrial communication networks.
Option D — PDH (Correct): Plesiochronous Digital Hierarchy provides access to legacy transmission services such as E1/T1, allowing continued support for existing communication infrastructure.
Option E — SAN (Correct): Storage Area Network services can be transported through compatible interfaces and optical transport arrangements. This is especially useful in data center interconnection and disaster recovery environments.
Option F — ETH (Correct): Ethernet service support enables the transport of modern enterprise data communications across the optical network.
The MS-OTN architecture enables several of these service types to share transport resources while supporting appropriate switching, grooming, and isolation.
Technical Conclusion: B, C, D, E, and F are correct. GPON is the only unsupported service-interface category among the listed choices.
In a coherent transmission system, if system dispersion and PMD are within the tolerance range, the dispersion penalty need not be considered.
TRUE
FALSE
Exact Extract — Network Planning, Design, Configuration and Quotation Guide, Page 51
“For a pure coherent system, dispersion does not need to be considered. Skip the step for configuring dispersion compensation.â€
Technical Deep Dive:
Coherent optical transmission uses advanced modulation formats and digital signal processing (DSP) to recover optical signals affected by transmission impairments.
Two important impairments are chromatic dispersion (CD) and polarization-mode dispersion (PMD).
Chromatic dispersion occurs because different spectral components of an optical signal propagate at different group velocities. In conventional intensity-modulated transmission, accumulated dispersion can introduce substantial signal distortion.
PMD arises when two orthogonal polarization modes propagate with different group delays. Its effect is generally characterized by differential group delay (DGD).
Modern coherent receivers employ DSP functions such as adaptive equalization and chromatic dispersion compensation to mitigate these impairments.
When the accumulated dispersion and PMD remain within the receiver ' s specified compensation capability and applicable zero-penalty operating region, additional dispersion penalties need not be included in the system design.
This simplifies WDM network planning because traditional dispersion compensation modules (DCMs) are not required solely to compensate chromatic dispersion in a suitable coherent system.
Eliminating DCMs can also reduce insertion loss, optical equipment requirements, and transmission latency.
However, designers must still evaluate optical signal-to-noise ratio (OSNR), nonlinear impairments, receiver tolerances, and system margins. Being within an absolute tolerance limit does not universally guarantee zero implementation penalty.
Technical Conclusion: A is correct under the stated condition that dispersion and PMD remain within the receiver ' s applicable penalty-free tolerance.
How many E9624 devices may be installed in a 19-inch cabinet?
2
3
1
4
Exact Extract — Huawei E9600 and E6600 Series Products and Industry Applications Introduction, Page 6
“Dimensions: 17 U high, 747.2 x 442 x 295 (H x W x D, unit: mm)â€
The same hardware introduction identifies installation in a 19-inch cabinet.
Technical Deep Dive:
The Huawei OptiXtrans E9624 is a high-capacity optical-electrical integrated transmission platform designed for enterprise backbone and aggregation networks.
Its physical dimensions are approximately 747.2 mm in height, 442 mm in width, and 295 mm in depth.
The device occupies approximately 17 rack units (U).
A standard rack unit measures 44.45 mm. Therefore, a 17U E9624 requires approximately 755.65 mm of nominal rack-unit allocation.
Assuming a 42U 19-inch cabinet, the rack-unit calculation is:
42U ÷ 17U ≈ 2.47
Only complete devices can be installed, so the maximum based on available rack-unit height is two.
Two E9624 subracks occupy 34U, leaving approximately 8U for supporting installation requirements.
Three E9624 subracks would require 51U, exceeding the available 42U cabinet height.
During actual installation, engineers must also reserve appropriate space for the power distribution unit, cable routing, ventilation, and other supporting components.
Technical Conclusion: A is correct for the standard 42U cabinet arrangement used by the question. The 19-inch specification defines mounting width; cabinet height must also be specified to establish the absolute device count.
On the SCT configuration-result page, some Sparts cannot be located. What could cause this?
Select All that Apply
They are filtered Sparts in the current wavelength selection.
The Sparts are removed.
They are filtered Sparts in the country where the BOQ is located.
They are filtered Sparts in the current VRC version.
The Sparts are displayed on the configuration board page.
Exact Extract — Network Planning, Design, Configuration and Quotation Guide, Page 61
“Wavelength Spectrum Range & Total Wavelength Quantity of System: Boards are filtered based on the wavelength spectrum range.â€
Technical Deep Dive:
Huawei ' s Smart Configuration Tool uses product configuration parameters and commercial eligibility rules to determine which parts can be selected or displayed.
A Spart represents a selectable part or sales item within the product configuration environment.
Several conditions may affect the visibility of a Spart.
A. Wavelength selection filtering
Optical boards, amplifiers, multiplexers, and related components are associated with specific wavelength ranges. If the selected optical spectrum does not match the supported configuration of a component, the configurator may exclude that component.
C. Country-based restrictions
Product availability can depend on the geographical market associated with the Bill of Quantity. Regional sales eligibility, market introduction status, and product restrictions may influence which part numbers are available.
D. VRC version filtering
Hardware and software compatibility depends on the selected product release. A component may be available in one release but not in another.
Version compatibility is important because hardware support, feature availability, and software integration requirements can change between releases.
Option B is not one of the three intended filtering conditions. However, permanently removed parts can also become unavailable in practice. Therefore, B is not an entirely impossible explanation for a missing item.
Option E concerns the location of an item within the interface rather than its exclusion by a configuration filter.
Technical Conclusion: A, C, and D match the intended filtering mechanisms. The training directly confirms wavelength-based filtering and separately confirms that removed products can disappear from SCT, making the question ' s treatment of B somewhat ambiguous.
Which of the following are key highlights of ASON 2.0?
Select All that Apply
Predictive rerouting, zero service interruption
Fast self-healing
Intelligence and reliability
Elastic large network
Exact Extract — Huawei E9600 and E6600 Series Products and Industry Applications Introduction, Page 4
“ASON 2.0: self-healing within secondsâ€
Additional Training Reference — Page 5
The E9624 reliability architecture identifies service-level protection mechanisms including client 1+1 protection, SNCP, optical-layer 1+1 protection, and ASON 2.0.
Technical Deep Dive:
Automatically Switched Optical Network (ASON) technology introduces intelligent routing, protection, and restoration capabilities into optical transport infrastructure.
ASON 2.0 enhances conventional optical protection through improved route computation, network scalability, reliability, and automated fault recovery.
Option A — Predictive rerouting: Intelligent network monitoring and route planning can help identify potentially deteriorating transmission paths and prepare alternative routes. When suitable protection and proactive switching mechanisms are available, service disruption can be minimized or avoided.
Option B — Fast self-healing: ASON automatically computes and establishes alternative transmission paths following qualifying network failures. This reduces the need for manual service recovery.
Option C — Intelligence and reliability: The integration of control-plane automation, topology awareness, path computation, and protection mechanisms helps improve network resilience.
Option D — Elastic large network: ASON enables optical networks to scale while supporting dynamic route management and efficient utilization of network resources.
Huawei ' s more recent optical backbone material also describes large-domain ASON 2.0 scalability and fast automatic recovery.
Technical Conclusion: A, B, C, and D represent the intended ASON 2.0 highlights.
Engineering qualification: Zero service interruption is not guaranteed for every type of failure or every protection configuration. The actual recovery performance depends on the protection scheme, failure location, service type, and availability of alternate network resources.
If customers require a quotation for spare parts, which of the following quotation methods should be used?
Manually insert a board in the SCT.
Add spare part product modules in the SCT.
Quote spare part services in the SCT.
Exact Extract — Network Planning, Design, Configuration and Quotation Guide, Page 58
“SCT is a swift, smart, and simple online tool that makes configuration and quotation easier, including data communication, data storage and intelligent vision, digital power, enterprise wireless, enterprise common, enterprise professional services, inverter, Huawei Cloud, computing, enterprise intelligent computing service, intelligent automobile solution, and transmission and access.â€
Technical Deep Dive:
The Smart Configuration Tool is designed to generate standardized product configurations and commercial Bills of Quantity for Huawei equipment.
When customers require spare parts, the quotation should identify the required hardware components as spare-part product items rather than treating them as installed service boards or maintenance services.
Spare parts may include equipment modules, optical transceivers, power components, fan assemblies, interface boards, and other replaceable hardware.
Adding spare-part product modules allows the configuration to distinguish between equipment required for normal network operation and additional inventory required for maintenance or disaster recovery.
Option A is not the preferred approach because manually inserting a board into an equipment configuration may cause it to be treated as installed hardware rather than as spare inventory.
Option C is incorrect because spare-part services generally refer to commercial support or maintenance arrangements, whereas the requirement concerns the supply of physical replacement components.
A professional spare-parts quotation must also consider hardware compatibility, replacement models, delivery restrictions, and current product availability.
Technical Conclusion: B is the appropriate product-quotation method. The uploaded training establishes the general SCT product-quotation workflow, although it does not expressly document this specific spare-part module selection procedure.
ODU4 supports 80 ODUk slices or 1,000 OSU slices.
TRUE
FALSE
Exact Training Reference — Huawei E9600 and E6600 Series Products and Industry Applications Introduction, Page 32
The Next-Generation Optical Network Technology diagram compares 80 slices per ODU4 in conventional OTN with 1,000 slices per ODU4 using Liquid OTN/OSU.
Additional Exact Extract — Page 23
“2 Mbit/s slicing, increasing the number of connections by 12.5 timesâ€
Technical Deep Dive:
ODU4 is an Optical Data Unit container used within the Optical Transport Network hierarchy, with a nominal client capacity of approximately 100 Gbit/s.
Traditional OTN uses predefined tributary-slot structures for multiplexing lower-order ODU signals into higher-order ODU containers.
An ODU4 can provide 80 conventional tributary slots of approximately 1.25 Gbit/s each, depending on the applicable OTN mapping arrangement.
However, conventional tributary-slot allocation may be inefficient when numerous low-bandwidth services must be transported.
Liquid OTN introduces Optical Service Unit technology to enable substantially finer bandwidth allocation.
Huawei ' s training illustrates an increase from 80 conventional slices to 1,000 OSU service slices within the same ODU4 capacity.
This represents:
1000 ÷ 80 = 12.5
Therefore, the number of supported service slices increases by a factor of 12.5.
Liquid OTN also supports service bandwidth allocation in fine increments, down to 2 Mbit/s in the described implementation.
The additional flexibility improves bandwidth utilization and allows more small-bandwidth services to share the transport capacity.
Technical Conclusion: A is correct according to Huawei ' s V1.0 training.
Terminology clarification: The conventional 80 slices are OTN tributary slots, while the 1,000 OSU slices represent a finer service-connection arrangement. These should not be interpreted as 1,000 equal-capacity ODU tributary slots.
Which of the following are selling points of Huawei’s transmission network solution for the transportation industry?
Select All that Apply
Hard pipe and low latency
Multi-service access (PCM/SDH/packet/video)
100G and beyond 100G high-bandwidth transmission
Physical isolation and high reliability
Exact Extract — E9600 and E6600 Series Products and Industry Applications Introduction, Page 45
“Hard pipe, zero packet lossâ€
“Ultra-low latencyâ€
“Various protections, guaranteed quality of mission-critical servicesâ€
“Physical isolationâ€
Technical Deep Dive:
Huawei ' s transportation transmission solutions are designed for railway, metro, and other mission-critical transport communication networks.
Option A — Correct: Optical hard-pipe transmission allocates dedicated transport resources to specific services. Unlike shared best-effort packet forwarding, this architecture helps deliver predictable latency and service isolation. Such characteristics are especially important for train signaling, protection, and dispatching systems.
Option B — Correct: Transportation infrastructure commonly operates legacy and modern communications simultaneously. Huawei ' s integrated transmission platform supports the convergence of PCM, SDH, Ethernet/packet, OTN, and video-related services, reducing the requirement for separate dedicated transport networks.
Option C — Correct: High-capacity optical transmission using 100G and higher-rate wavelengths provides the bandwidth required for railway backbone expansion, video monitoring, digital infrastructure, and future service growth.
Option D — Correct: Transport networks must remain available despite equipment failures or optical cable faults. Protection mechanisms such as SNCP, client-side 1+1 protection, optical-layer protection, and ASON-based restoration contribute to service continuity.
Physical isolation further protects critical traffic from interference associated with unrelated services sharing the transport infrastructure.
Technical Conclusion: A, B, C, and D are correct. Together, they describe Huawei ' s high-capacity, low-latency, converged, and resilient transportation transmission architecture.
Which of the following boards does the OptiXtrans E6608T support?
Select All that Apply
AST2 board
Ponder board
OAU
TTA tributary board
Exact Extract — Network Planning, Design, Configuration and Quotation Guide, Page 70
“The OptiXtrans E6608T functions as the optical-layer chassis of the OptiXtrans E6616â€
The same configuration rule specifies that only optical-layer and Ponder boards are supported in the described chassis role.
Technical Deep Dive:
The OptiXtrans E6608T is designed primarily for optical-layer transmission and wavelength-processing applications.
Its architecture differs from the E6608 and E6616 because it does not provide a centralized electrical cross-connect matrix.
The E6608T supports optical-layer functions and compatible optical transponder boards.
Option A — AST2 board (Correct):
AST2 provides optical supervisory channel and monitoring functionality. Supported AST2 implementations include embedded OTDR capabilities used for optical fiber supervision and fault localization.
Because AST2 is associated with optical-layer monitoring, it is consistent with the E6608T ' s supported optical board architecture.
Option B — Ponder board (Correct):
Ponder boards support optical transponder and muxponder functions. They enable client signals to be mapped or aggregated into higher-capacity optical wavelengths.
Option C — OAU (Correct):
The Optical Amplifier Unit provides optical amplification functions used to compensate for transmission attenuation and maintain adequate optical power levels.
Option D — TTA tributary board (Incorrect):
A TTA tributary board is an electrical-layer service-processing board. It is not supported in the E6608T optical-layer/Ponder-only configuration described in the training.
The distinction is important because equipment selected for optical wavelength transport cannot automatically be assumed to support electrical service grooming.
Technical Conclusion: A, B, and C are the intended selections.
Configuration qualification: Board compatibility must be checked against the exact chassis role and software release. The uploaded guide explicitly establishes the optical-layer/Ponder restriction for the described E6608T configuration, rather than documenting every possible standalone operating mode.
TESTED 19 Nov 2026